Flux-Off Complete

Flux-Off Complete Flux Remover is an extra strength solvent that removes heavy and encrusted flux residue. This unique solvent based formulation penetrates quickly to remove all types of flux, oxide particles, dust, grease and oil, then evaporates quickly leaving no residues.

CLICK HERE FOR FLUX REMOVER SELECTION GUIDE

Features & Benefits

  • Powerful cleaner removes R, RA, RMA, and No Clean fluxes
  • Extra cleaning strength
  • Non-corrosive, safe for metals
  • Dries fast
  • Leaves no residue
  • Flammable
  • All-Way Spray valve - even sprays upside down

Applications

  • Removes all types of rosin-based and synthetic no-clean fluxes
  • Minimizes white residue formation
  • Can replace MEK in cleaning applications

Swipe to View Add to Cart Button 

Part # Size Units Per Case Price Per Case Add To Cart
ES1698

12 oz./ 340 g aerosol

12 cans $270.84
ES198

1 gal / 3.7 L container

1 container $92.56
ES598

5 gal (18.5 liters) pail

1 container $258.35
ES5598 1 container $2,528.50
Order from an authorized distributor

FAQ's

How do you use an aerosol cleaner?

Hold object to be cleaned in vertical position. Pull trigger gently to control solvent flow rate. Scrub with brush from top to bottom, allowing the liquid to flush away contaminants. 

How do I properly dispose of an aerosol can after it is empty?

It may be different state-by-state, so contact your state environmental agency for regional specific regulations. For a general guideline, here is the process according to EPA hazardous waste regulations 40CFR. The can has to be brought to or approach atmospheric pressure to render the can empty. Puncturing is not required, only that it “approach atmospheric pressure”, i.e. empty the can contents until it’s no longer pressurized. This insures that as much contents as is reasonably possible are out of the can. It is then considered “RCRA-empty”. At that point it can be handled as any other waste metal container, generally as scrap metal under the recycling rules. Note that the can is still considered a solid waste at this point (not necessarily hazardous waste).

Is there something I can do with the extension tube (straw) so it doesn’t get lost?

The red cap on Chemtronics aerosol products like flux removers, degreasers, and Freeze-It Freeze Spray has a notch on the top. That is engineered for the straw to snap in and hold into place so you don’t loose it. The aerosol trigger sprayers that are common on dusters, freeze sprays, and flux removers, have two ways to store the straw when not in use. The hole at the back of the body of the sprayer is just the right size for the straw to slide into place for storage. The slot below the trigger is also the right size for the straw to snap into place, which also has the advantage of locking the trigger.

How do I figure out the shelf life of a product?

The shelf life of a product can be found on either the technical data sheet (TDS), available on the product page, or by looking on the certificate on conformance (COC). The COC can be downloaded by going to https://www.chemtronics.com/coc. Once you have the shelf life, you will need to add it to the manufacture date for a use-by date. The manufacture date can be identified by the batch number. The batch code used on most of our products are manufacture dates in the Julian Date format. The format is YYDDD, where YY = year, DDD = day. For example, 19200 translates to the 200th day of 2019, or July 19, 2019. This webpage explains and provides charts to help interpret our batch numbers: https://www.chemtronics.com/batch-codes.

Articles

Flux Remover Video User's Guide

Flux Remover Video User Guide CLEAN WITH OVERALL SPRAY   |   CLEAN WITH EXTENSION TUBE / STRAW   |   CLEAN WITH BRUSH ATTACHMENT Flux removers are used to clean flux off printed circuit boards (PCBs), which is left behind after the soldering process.&nbs...
Read This Post

Ultimate Guide to Cleaning Electronics

In the process of assembling, reworking or repairing printed circuit boards (PCB) for electronic devices, the discussion inevitably turns to whether or not to clean the PCB. Cleaning adds time and expense to the process, and doing it wrong can cause more harm than good. This guide will walk yo...
Read This Post
You did not finish submitting your information to request a sample